Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hardware: NFR51822_QFAAC0
Firmware: S110_7.0_SoftDevice
SDK: NRF518_6.0
Application: ble_app_hrs in NRF51822 S110 Examples
I start a timer to toggle led once per...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...
Hi,
I have application where I drive LEDs with shift registers. I need to send 14 bytes via SPI every 200us while I am in BLE connection. Timing should be exact as shift...
Hi,
I have a project where I need to communicate using UART BLE between nRF51822 and a PC (MS Surface Pro 3) with Windows 8.1 and embedded BLE hardware.
I have programmed...
Hi,
I have downloaded nRF51_SDK_7.0.1_1d6e5cb.zip and run nRF51_mdk_6_1_0_installer.msi
Neither zip file nor created Nordic Semiconductor/nrf51/ folders have ewp or icf...
Hi,
I think it's a simple question. I want to connect a micro to communicate with a phone via the nrf8001. I ported everything thanks to the guide that you posted (for...
Can we use the tx_complete.count given with BLE_EVT_TX_COMPLETE as an indication on how many packets were sent out from the last ended connection interval?
thank you
...
I have a custom board utilizing an RF51822aa device. To test connectivity to the board I built blinky_s110_pca10028. Using Keil 5.12 I tried to debug the program simply expecting...
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash Download...
where can I get working sample code of nrf51822 with nrf24l01
including code of nrf51822, and code of nrf24l01, both TX, and RX.
in my application, I need 518 to RX data...
I am working with a university project where need to connect up to 20 wireless sensors together with 1 master, which will be communicating with either a computer or smartphone...
