Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I can successfully download an image using nrfutil dfu serial when I use a test image (compiling the bootloader with the Nordic default public key) and the application starts...
Hi,
My requirement is to validate the PCA10040 dev board with a different set of UART pins. I have tried the following steps, but as soon as I start the firmware, it crashes...
Hello, I am new to BLE development and RF design. I've been doing as much reading as I can about RF design rules for PCB's, antenna performance, etc. Yet I am still uncertain...
I am trying to get a BMX160 working over SPI. I was following this post to make this code using the SPI example from the SDK as a basis. I am using SDK 15.3 with a nRF52840...
The app is foreground -> I am very easily connected with BLE device.
The app is in the background -> I get the callback and connect with the BLE device
The app is removed...
Hello.
I'm trying to get the example bootloader Segger project (secure_bootloader_ble_s132_pca10040) running on a custom board I have that uses the nRF52832 as its core...
I am working on nRF9160 and i found that when i change prj.conf, i need to rebuild code. if rebuild is not done(only build is done), changes made in prj.conf does not comes...
Hi
I'm currently evaluating the possibility of using nRF5340 in an upcoming project. As the chip is very new it's easy to understand that all specifications are not yet...
Hello, I am using nRF SDK for Mesh 3.1 and nRF52940 SoC. I have two nodes in my network which both act as a client and a server. Both of them subscribes and publishes to same...
Hi,
I am working with ANT bpwr tx profile and trying to implement HX711 and TWI sensor to it. TWI sensor is already working, but when I add library for HX711 from and start...
Hello,
It would be nice if the HVN tx complete event structure had the attribute handle of the characteristic that was just notified. This is already done for writes and...
Hey guys,
I'm working with the Laird DVK-BL652 and the Nordic SDK v.14.2.0 with Eclipse (Kepler) and try the example "SPI Master". I didn't modify this example but after...
Test Setup:
SD 6.1.0
SDK 15.2.0
Peripheral: nRF52840
Central: iOS 13.1
Central is connected to two peripherals, each peripheral is sending 50 pkt/s, each packet...
Hi,
We have a nrf51822 based custom board with no button, we use accelerometer tap detection to wake up the system. Currently there is no software protection for the battery...
After getting my nRF9160DK activated and showing up in the NRFCloud it would just sit there blinking led3.
I deleted the device from the cloud and tried to update modem...
