Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi
I'm using the unmodified fatfs example in SDK16 with PCA10040 dev board connected to a Mikroe SD-Click board which is nothing more than a breakout board for microSD cards...
It is possible to provision the NetKey, AppKey and unicast address of a node using the serial protocol, using the following messages:
Mesh Subnet Add, Opcode: 0x92 - NetKey...
Dear Sir or Madam,
It´s the second time, I got the same error while start developing with nrf52833 demo board. For first step, I flashed a blinky example to the board -...
Now I'm trying to change a device name in `nrf_dfu_ble.c`. I set NRF_DFU_BLE_ADV_NAME like following.
And I imported `stdio.h`, `string.h`. And I edited `gap_params_init...
Hi,
im trying to flash a 3rd party demo board (MDBT50Q-512K Module Demo Board) with nrf connect for desktop. As programmer I use original Segger j-link edu mini.
As...
Dear Nordic:
My peripheral is configured to use MTU 247.
When connected by NrfConnect of IOS, I can receive NRF_BLE_GATT_EVT_ATT_MTU_UPDATED event and check the effecitve...
We are designing in the 52840 as a processor in a new sensor product and are looking at using the HOLYIOT YJ-18010-nRF52840 part that you indicate on your site is a third...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
Hi!
A little backstory on my project: Currently I have merged the saadc and peripheral ble_app_uart example. The value from a potentiometer is then sent over ble to the...
Hi,
I'm developing a project with nrf52832 sdk 16.0.0. I have some issue about the fds. peer_manager had used the fds modul, as we knew. And I would call fds_record_write...
