Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi all:
So I'm going straight to the point, I have a board with NRF51822 that I dump the flash and programmed with another one, after that I notice that the firmware I...
I recently purchased the nRF5340 PDK. I am working through the getting started guide and can't seem to get the Heart Rate Monitor demo application working.
Firstly, when...
trying to get nrfutil working on ubuntu, following this guide:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html
after...
hi, I have used to segger j link basic with nrf connect programmer to program mass production.
but, It takes 30 seconds. For better efficiency, can It be improved to change...
Hi Everyone,
I need to develop a bootloader and a firmware update procedure.
My development environment is nRF52840, sdk 15.3.
Program download configuration 1) Download...
Using Mesh SDK 3.2.0.
The returned Device Composition Data is malformed when requesting it after the node has been reset. This is because the sig_model_count and vendor_model_count...
Hi to all,
i am trying to develop an app with NRF52840 soc and nordic sdk 15.03. in my app i implemented a usb hid device and also i am using flash storage at same time...
Hi
After getting SDK16 , we have tried to load a combined hex file with bootloader + S132 V7 + application with dfu + bootloader setting page to PCA10040. And It work well...
Hi,
i am working with aws-fota example, i copied my certificate to certificate.h file, once i run the program it shows like
The MQTT AWS Jobs FOTA Sample nrf_inbuilt_key_delete...
Hello, I started to delvelop an program from mqtt simple, now that I almost finished I saw that mqtt is refusing to connect to my broker, I deleted all my code I wrote and...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
