I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am currently evaluating the nRF54L15 dk and porting the old project code from the nRF52DK to the new nRF54L15DK devboard. However, I have encountered an issue with...
I would like to use NRF Desktop Connect to connect to, and potentially firmware update an nrf52832 via the onboard bluetooth, but the NRF Desktop connect is only available...
Goodmorning,
I developing an application on nrf52840 board with SDK15.2.0 that communicates via BLE with from the APP nordic. I am started from the example project ble_app_cscs...
So I'm trying to implement Mesh OnOff server with BLE DFU supports. My implementation is as follows:
These are my app_config.h and nrf_mesh_config_app.h
I face...
Hello,
I am trying to use several Thingy 52 as peripheral devices, (sensors) connected to a central (Gateway) particle Argon running ( nRF52840). The idea is to connect...
Hi, I have 2 questions regarding multiple controllers using nRF Mesh.
1. I used the import/export option to transfer the network details from Phone 1 to Phone 2. After import...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
Hi there,
I'm trying to use the aws_fota example with nrf9160 and AWS and it works fine. The problem is that in my country we don't have LTE-M, so we decided to use a...
Hi,
My application returns ERROR 8 [NRF_ERROR_INVALID_STATE] after I click disconnect in the app "nRF connect for mobile" .This error is returned by "ble_advertising_start...
I try to run samples/bluetooth/scan_adv on nRF52840/nRF5340 using nRF BLE Controller..
Result is nRF52840/active scan: 498 packet/s nRF52840/passive scan: 507 packet/s ...
