Hello Nordic team,
I'm working with the nRF54L15 DK and using the latest NCS version that supports Bluetooth Channel Sounding. Here the sample is channel_sounding_ras_initiator...
I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
I'm looking at a BLE application using the nRF51822 where we need to send data maybe once every 10 minutes, so it seems like disconnecting in between sending messages will...
Hi,
im using nRF24L01+ to constantly transmit data and all working fine, but at some point SPI fails and the only returned values I get are 0x0F - doesnt matter which register...
Hi sir
In order to simplify the flow of programming hex file to nRF51, we want to merge Softdevice hex file with application hex file. Then, generate a new hex file. Could...
I have attempted to put the radio into +4dBm mode using the command: sd_ant_channel_radio_tx_power_set(CHANNEL_0, RADIO_TX_POWER_LVL_3);
When I look at the RADIO TXPOWER...
I just got the nRF51822 DK and tried hooking up the dongle. I am using Parallels 9 on OS X 10.8.5. It only loads as a uSB Composite device with a yellow warning icon. Odd...
Hi
I am trying the nRF51822 Evaluation Kit for the first time.
I have followed the instructions in the User Guide v1.1. The blinky_example works fine, indicating that...
Have you also wondered how to get serial IO (UART) with nRF51422-EK via the Segger debug interface?
[list=1]
[ ]Plug Eval kit in the USB port.
[ ]In Windows open "device...
Hi,
i need to stop one of my Timer at the falling edge of a Pin. So i need a gpiote_interrupt, is this right? Can someone help me how i can do this? if i write something...
I have 3 inputs I need to sample every n minutes. I have an n-minute timer that can kick off the first one, but I need to run the second and third samplings in succession...
We are creating our own dev board.
What pcb parameters were used for the PCA10004-nRFgo PCB antenna radio module 2.0?
1.6mm?
1oz Cu?
impedance control?
I have not...
Hello,
We want to use the J-Link Needle Adapter for nRF51822
The attached (capture.jpg) is the pinout from the J-Link Needle Adapter datasheet.
the attached (capture2...
Hi,
I have a wired problem with the nrf51422,
I'm loading the code using the J-link into my board or the evaluation board (PCA10007) that I have, the code runs perfect...
Hi all, I met a problem with measuring lithium battery voltage. I used 1Mohm and 250Kohm divided voltage, and used the internal VBG voltage as reference, and used ADC0 as...
I'm using a nRF51844
I'm writing my own ADC reading routines because I can't find any examples, but I know how to code so that's not a problem. I just want to confirm something...
Hi,
does a code example or app-note exists that describes how to configure the SPI peripheral to use an ISR to transmit data to a SPI slave?
Thank you in advance!
