Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi I created a custom board with nRF9160SiP
I follow the same schematic og Thingy:91
I ran some tests with VNA to see if the antenna matching was correct, and I see that...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hello
Does the green box directly determine which version of the lib to use[ lib_openthread_mtd.a ]? If so, what is the purpose of the red box? If I change the red box to...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hello,
I have an application running with a BLE peripheral and our proprietary TSCH wireless stack using an integrated radio. The hardware sharing is done through the MPSL...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
