Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hello! We have an app with bootloader on SDK 15.3.0. Is there a way to jump from application into bootloader without setting byte 0 of GPREGRET register? I.e. without this...
Good afternoon,
First of all, I hope that you are all well and are able to work from home, regardless of the government instructions of your country of residence.
My question...
Hello,
Does Nrf mesh SDK supports Kiel tool chain or anyother free tool chain?
My Segger Embedded Studio(3.28) License is over and I cant modify and build the code.
...
Hello everyone:
I would like to make nrf52810 as a beacon.
My problem is how to make the beacon can also scan the RF channel-38 after advertising ？
Which softdevice...
Hello,
I'm setting up a dev environment on a new machine. I installed SEGGER Embedded Studio v4.52a and nRF5 SDK v16.0.0 and nRF5 SDK for Thread and Zigbee v4.0.0. For the...
Hai ,
In my application need to merge peripheral and central of app_blinky example.
1. My pheriperal part of NRF52840 is always connected with my client third party( ESP32...
I have created 2 custom services and its characteristics
one service has 3 characteristics and another service has 6 characteristics.
my issue is when I'm trying to notify...
Hi,
I'd like to update firmware on my nRF52832 panel with my update flow (only the application; the bootloader and softdevice will be unchanged). I can load the new firmware...
I cannot step through source c code, only disassembly. This only applies to custom source, such as main, that appear not in the SDK file folder but the code that resides in...
Hi,
We are developing an android application using nRF51422 to connect the BLE device, discovering characteristics and sending commands to the device. Here we are facing...
Hi, im working with the Arduino Example called pingpair ack. Sometimes I get this "Blank payload". ¿What does it means? The message was correctly recieved?
Sometimes I get...
Hi!
I'm not good at C and microcontrollers programming. Could somebody clarify, if nrf_rtc_counter_get interrupt safe? It just reads value from rtc register->COUNTER (24bit...
Hi,
When I enabled NRF_BL_DFU_ENTER_METHOD_PINRESET.
The 52840 Dongle into the DFU mode every time hardware power reset.
Use other DFU enters method does not have this...
