Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
Hi,
Does SoftDevices v7.0.1 supports Multiple Advertising Sets feature? I read that Softdevice v6.1.0 does not support the Multiple Advertising Sets feature. Let me know...
Hi. I was wondering if maybe you know where can I find the PCB desing of any of this modules: NRF24L01+ (the black one) or the SMD version. I only can find those pictures...
Hi gays,
Now, I want to c ollect a pulse waveform(example : 1s, 50% duty cycle ) which accuracy requires milliseconds resolution and I use PPI to read a capture value from...
Hi,
We have a custom board that uses an nRF52840. All our development is done on Win 10 based PCs. Our custom board is connected to our Win 10 based PC via USB and when...
Hello Sir,
We are using NRF24L01+PA+LNA SMA Antenna for transmission purpose using arduino using RH_NRF24.h library.
It is been set to 0dBm transitting power by default...
Hello,
I am working with nRF SDK V 16.0.0. I am using peer manager for my application, can I store my application data too using peer manager? if yes, please help to do...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
Hello,
I am implementing ble advertising using below code, i encountered a strange behaviour with this code. If jlink is connected the advertising works just fine. if I...
I have created one characteristic in which i am trying to write multiple bytes at the same time i want to use that for further processing, how to access that whole data which...
Hi,
I just started working with Nordic nRF52840 serial interfaces,can you please tell me which one is best for serial communication among SPI and I2c and why?And can you...
Hi Nordics, I know it has been asked over and over again about doing DFU of slave nrf52 using a central nrf52. devzone.nordicsemi.com/.../ota-dfu-application-firmware-by-ble...
Hi we are trying to program code using the SDK v12.3 library onto a custom NRF51822 board using SES. The custom code contains B luetooth routines, GPIO routines, and TWI routines...
