void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I need to read data from sensor and publish it to the mesh network. So the question is do I need to create Sensor model for that or, as in one of your replies , you suggested...
Hello Nordic Team,
I want to connect peripheral using Mac address, i am setting mac address filter in Scan init but Filter is not getting set
below is my Scan init function...
Hi there,
We have a network of zigbee with XBee-PRO modules working as co-coordinators and end nodes. I have to use BMD340 zigbee node to join that network as well. We have...
Do you have any example which is using NRF_SDH_DISPATCH_MODEL_POLLING for advertising, as well as scanning.
In nrf_sdh.c file, there is only interrupt mechanism in example...
I have an nrf52840 dongle. I can enter into DFU mode and the nRF programmer application recognizes it and shows the memory layout.
When I copy sniffer_pca10056_129d2b3...
Hi,
I am using nrf52832 for advertising and scanning. My board stops advertising after disconnecting.
I am calling all initializations (like ble_stach_init() ) from my...
Hello Sir is it possible to test Zigbee Coordinator project with one nrf 52840 board and one Hue bulb
Example from light control example ->light-coordinator
Hi Support,
This issue happens in nRF5_SDK_16.0.0_98a08e2 and nRF5_SDK_15.3.0_59ac345.
Directly import the example from SDK (examples\peripheral\flash_fds) into SES, build...
Hi,
I'm trying to get NRF Connect 3.3.0 connected to a nRF52 DK with a PCA10040 and get the following when I try to connect to the device: Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
I'm having some issues with the example provided in $MESH_SDK/examples...
Hello everyone,
I just started working with 802.15.4 using nRF52840. I wanted to know weather we can do RX-to-TX using 802.15.4. If yes what are the API's available to do...
We have problems with the restart which the application does after receiving the DFU attribute is written.
Startup should work like this as I understand it: the reset vector...
I have 2 hardware revisions, one with the GPS LNA attached to MAGPIO0, the other revision, the LNA is on COEX0.
In my prj.conf file, I have the following setup for handling...
From this guide:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h61sjziauupw1j397q9s9ldr01q4j6d5
Appendix...
