Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm using PCA10040 to test nRF52832.
But I can't see J-link device after connecting USB.
I installed J-link(segger), nRFgo studio, nrf command. But I can't see my PCA10040...
Hello, we are using the ble_app_uart example code, and are trying to modify it so that if a certain UART sequence is received from the connected microcontroller, it will disconnect...
Hi
I'm working on a project interfacing the nRF52840 board with the lis2dh12 accelerometer
I'm using SDK 15.3, basing my code on the provided driver and information...
Hello!
Now I have two devices about nrf52832 .One is central and another is peripheral. So I want to transfer the peripheral mac address to the central via nfc.
I do...
This is the config fun followed。
one sample every 125ns,one ant get 12us =96 samples.
and first 2+32 samples is ignored。
*******************************************...
I've already tried to set some zephyr configs, but n51822 to run as peripheral it nedds at least ~20KB
Have anyone got success or all the nrf51822 QFAA H2 will really never...
development environment： SDK 14.2 , NRF52840 as central and NRF52832 as periph for Bonding: Passkey Entry, Central displays, and the error occur on nrf52840.
I want to know...
Hi all! I am currently using an nrf52840, mesh sdk v3.20 and sdk v15.30
I have the following scenario which I am trying to solve:
I am receiving a new GAP name for each...
In an earlier thread ,
[quote userid="17188" url="~/f/nordic-q-a/33649/j-link-the-firmware-of-the-connected-j-link-does-not-support-the-following-memory-access-read-0x02000004...
I'm using the nus_c service with multiple central connections. Obviously, I need the connection handle in my event handler - ble_nus_c_evt_handler(ble_nus_c_t* p_ble_nus_c...
Our product use two NRF24L01+. One is for transmitting and another is for receiving. They communicate by 250Kbit/s. It is pre-production.
Now, we want use nrf52810 to instead...
I just trying log via Segger RTT viewer, followed the the same procedure as that of serial_lte_modem sample in my new project and could not see logs showing in the viewer...
I am working with nRF52 DK, SES4.30 and SDK 15.3 with SD 132.
This error just started occurring once I set up app_timers. My code for setting up my timers is below:
...
Hello,
I ordered a nRF5340-PDK board and i'm trying to get it to work.
When flashing the Heart Rate hex file I couldn't find the device (i pushed the reset button)....
