Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
hi
i am using sdk for mesh v3.1.0 i get my data from the uart and sending it over the mesh. i have been getting an error within the function net_state_seqnum_alloc() that...
Using SDK nrf52_sdk_16.0.0 PCA10040 S132
My code can read and write Flash using the "Data Storage Flash" interface, IE calling fds_record_write(...) and waiting for events...
Hello I am quite new to the hardware encryption topic and I have the following questions.
On a device where the MCU samples a sensor data and stores it to a external IC...
Hi .. I've a Chinese watch with NRF52832 CPU DTNO.1 F18. I'd like to change it watch face as all watch with Mediatek CPU ..
Is there an application to easily do that How...
I have a BLE application that I successfully program onto the dongle by pushing the reset button on the dongle and using the "programmer" application from nRF Connect.
The...
To demonstrate installing the tools for my client I'm going through the process first, on a fresh machine.
Installed SES & invoked it. Got a free license & installed it...
I have a new nrf 9160 DFK. I followed up the instructions from 'Getting Started Assistant' from the 'nRF Connect for Desktop' app. I was able to setup and build the asset...
Hi,
Our company use nrf24L01+ for many years,the maximum output power of 24L01+ always about 0dbm in our application.But recently we meet a problem that the 24l01+ output...
Hello, as mentioned in subject, I have done DFU on nrf51 DK. it is tottaly working fine. As soon as I try to work with Nrf51822 QFAC custom board. It goes in to bootloader...
Hi,
I intend to use the nRF9160 as an LTE module. I will send data to be transmitted to the nRF9160 and receive data from the nRF9160 via SPI. I have read in numerous places...
I just want timer2 to run at 1Mhz so I can grab a microsecond counter as a timestamp. I don't care that it'll overflow after 32 bits. Put together what I thought should be...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
As per the section - "Adding support for programming nRF5340 in SES" in the document https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html , I had...
