I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
Hi everyone,
my problem is pretty simple: we developed a custom board for the NRF52840 to work using a custom protocol or BLE. A few sensors are connected to the NRF using...
Hi,
I am using NCS v1.1.0 and modem fw 1.1.0.
We had prepared our application in NCS v1.0.0 and now i have moved it to v1.1.0.
In new sdk v1.1.0 ,When i try to get Address...
Hello , I am advertising from a nrf device with advertising interval of 40ms. and I want to measure this interval at scanning side.
How I can measure using timer , timer...
I am using nRF52 DK to evaluate the TX power settings using sd_ble_gap_tx_power_set command:
sd_ble_gap_tx_power_set ( BLE_GAP_TX_POWER_ROLE_CONN , m_conn_handle, tx_power...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
I am looking to use libuarte in our project. We are creating a battery powered device and so need to be low powered. EasyDMA draws about 1mA when running which is far too...
Hello,
We are developing an application that is trying to receive a steady stream of bytes from a serial port. But we constantly get a fatal error when we call app_uart_get...
I'm running 6 X Thingy:91s in pre-production for use as a GPS tracking/iOT solution. Currently I'm located in Austin, TX. If I do not request GPS, I receive regular data from...
Hi all, I'm working with NRF52DK using Segger Embedded Studio with NRF SDK 15.0 trying to communicate to a UART sensor using the serial port abstraction layer API. Following...
Hi all, I'm facing an issue communicating with a UART-based sensor on the NRF52DK (52832). I've followed the serial_port example and using various forum topics I've got to...
Hello,
I am using the nrf52832 bootloader and i got it working with the s112 sofdevice and a custom application mapped at the end of the softdevice.
I want to add another...
