At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
from this guide
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h23sjziacp7vrw0scs2t3tua1ax0426
It is...
Good evening.....
I am looking to play around with the Thingy 91 but I am a hardware guy who knows enough about firmware to be dangerous. I typically run into issues getting...
Hi,
I am trying to send firmware image from one board to another board. For that I want to use DFU control point characteristics.
I am using nrf52832 development kit...
I have installed the cocoapod for nrfMeshProvision, but i am new to BLE technology. I am able to fetch the dataIn and dataOut characteristics, but stuck at creating a Proxyhandler...
Hi,
I have a project where we want to setup 3 PWM channels for dimming LED strings in a mesh configuration. So the mesh dimming server is a perfect starting point. I did...
Hello,
Our team is new on development nRF52832 firmware.
Now we have an issue on standby current for nRF52832.
We have a 5 second timer for a PWM output.
Sleep (System...
Hello there,
I am facing some difficulties while using nRF52832 NFC for an application.
When I tap the nrf52832 device on the NFC reader the nrf52 cannot able to respond...
Hi, we are currently looking at making a zigbee light switch using the 52811. However since the zboss library files are compiled with FPU directives the only way to build...
I need to read data from sensor and publish it to the mesh network. So the question is do I need to create Sensor model for that or, as in one of your replies , you suggested...
Hello Nordic Team,
I want to connect peripheral using Mac address, i am setting mac address filter in Scan init but Filter is not getting set
below is my Scan init function...
Hi there,
We have a network of zigbee with XBee-PRO modules working as co-coordinators and end nodes. I have to use BMD340 zigbee node to join that network as well. We have...
Do you have any example which is using NRF_SDH_DISPATCH_MODEL_POLLING for advertising, as well as scanning.
In nrf_sdh.c file, there is only interrupt mechanism in example...
I have an nrf52840 dongle. I can enter into DFU mode and the nRF programmer application recognizes it and shows the memory layout.
When I copy sniffer_pca10056_129d2b3...
Hi,
I am using nrf52832 for advertising and scanning. My board stops advertising after disconnecting.
I am calling all initializations (like ble_stach_init() ) from my...
