Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I can't get flashlog/crashlog to work properly. The symptoms are that when NRF_LOG_BACKEND_FLASH_START_PAGE is set to 0 (i.e logs are written to address right after the application...
I have a nRF528420 [on Skylab module SKB501] and have wired up a custom connection to USB. I'm able to program NRF52 with both softdevice S140 and BLE Peripheral ble_app_uart...
Hello,
I try to add watchdog on aws_fota sample but Something is wrong about bootloader to application transition and it always reboots.
00> [00:00:00.051,513] <inf> mcuboot...
Hello everyone,
I have found the following issue in the behavior of the SPI driver:
having connected an NRF52840 as an SPI master which is set to receive 22 bytes from...
My peripheral uses "LongWrite". Communication with Central has been successful. I want to know the length of the written data. After trying the following, the obtained result...
I’ve been developing the FW for an nRF52832-based module that controls a simple lighting product.
The capabilities include support for secure DFU and a modified version...
Target : NRF52832 as Server
Description of the problem (seen in wireshark)
Client : write request (0x12)
Server: Rcvd Error Response - Invalide Attribute value length...
We're porting an nRFS52832 app from an earlier version (14) to 15.2. Using sd_ble_gap_device_name_set( &secMode, dN, len ) with a string of length=9 will only show 5 chars...
Hi, we are trying to get the nRF9160 connected to the internet again, we had it working 6 months ago.
Our hardware is 0.8.5
We are in Ireland where we only have NB-IOT...
Hi
I'm using the watchdog of the nRF52832 Rev. 1.
The PS V1.4 states that the maximum run current of the watchdog is 2uA while the typical current is only 0.3uA. Can you...
Hi,
I am migrating from SDK14.2 to SDK15.0 and I can compile now, but when runnning the nrfx_uart_init the hardware handshake signal RTS is high from the beginning.
...
I am running into compile errors in different places in the SDK where there are lines as shown below: #if (NRF_BLE_GATT_ENABLED) /* do something */ #endif It is a widely and...
Hello Team,
Currently, we are evaluating nRF52 using nRF52840DK for one of our upcoming project. Basically, our typical application involves sending 32 Bytes of command...
I am using nRF52840dk SDK15.3.0 ble_app_att_mtu_throughput example,in that example i included some part of ble_app_uart code. Now the issue i am facing is ble_link_ctx_manager...
