Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...
We are using a custom board with an nRf9160, and have tested it with several sim cards. The board has been tested with a spectrum analyzer and it is able to transmit RF, however...
I'm having trouble with PDM on SDK15.2 with nRF52840.
The raw data buffers are only half full. The last half are zero's, therefore recorded voice has a robotic sound to...
Hi!
I am trying to use my own repo like described in the tutorial https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/nrf-connect...
I want make connection secure between mobile app and thingy52. What are the types for secure connection. Currently anyone can connect thingy without any permission.
I have setup zephyr development in an ubuntu 18.04 virtual machine. everything is working fine. but can't see the vcp. i disabled and enabled it in the jlink configurator...
Dear Nordic representative,
I would like to run qualification BLE tests on nrf52832 chip: - https://docs.zephyrproject.org/latest/guides/bluetooth/bluetooth-qual.html
...
Dear All,
In my application I need to switch on and off the modem using AT+CFUN=0 and AT+CFUN=4 respectivelly. My question is the following. Let's assume that the device...
SDK:V15
chip:52832
development kit:window+keil
In stm32,inder to use uart rx with DMA, we could easily use:uart Idle interrupt+dma.but how in 52832 while how many...
I’m looking at this example:
https://github.com/NordicPlayground/nrf5-calendar-example
which uses standard C function localtime(), but can not find neither in the example...
Hi devzone,
I learnt DFU through USB by performing the following steps:
1. build and run "secure bootloader usb" project with segger through J-link port J2.
2. flash...
I'm setting up a new project (solution?) for the nRF52-DK, using SEGGER, based on one of the examples in the SDK, and would like to put it under version control (Github, etc...
Hello , I m working on project to commande sim868 by serial (send AT Commands), so for the fisrt i would like to test the serial connection with an arduino to see what it...
