I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I got the dev board all set up and working - managed to program a few examples flashing LEDs etc…. So then I wanted to do a BLE peripheral beacon example and it told me to...
I'm looking at designing my own Bluetooth Receiver essentially. Playing music from my phone to a Bluetooth receiver, to output via AUX.
I was looking at the range of MCU...
Hi,
For my all DFU i follow the steps on the Getting started guide , just in the Performing DFU step i use the nrfutil tool for the over USB.
First i tried with the DFU...
Hi team,
Similar to how we have recommendations to use certain pins for low drive, low frequency on the nRF52 series, do we have those recommendations available for the...
nRF connect is not recognizing my nRF9160 board when I try to use the programmer tool. It allow me to select it from 'select device' drop down menu. But then I select it all...
Hi,
I am working with NRF52832 boards where on one board i have loaded Multilink central example, and on the other i have loaded peripheral code with some modifications...
I have merged Light and DFU examples(Light_DFU), and test DFU update both blinky and Light_DFU.
It is always getting ERROR_BUSY (134) while update Light_DFU, but success...
Hi, do you have a schematic / diagram that shows the architecture of the asset tracker application / nRF Cloud?
Does it use MQTT for communication?
Does it use the AWS...
Hi there. I'm developing an NRF52840 project from scratch and wanted to obtain a "good reference" sdkconfig.h . I tried picking one from the examples (the UART example, 'cos...
Hello guys I am using nrf52832 dongle for development and my client has nrf52832 DK at the moment. I have completed my firmware that get ADC values and store data on SD card...
So, we have a problem that the new Samsung S20+ phone is not able to connect to the nRF52833 if extended advertising is enabled (using nRF Connect for Mobile app).
The phone...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am using app_timer to control the LED On time.
the app_timer...
Hi,
I am using nrf sniffer. I have used both nrf51422 and nrf52832. Here I am facing such kind of issue like. Once I am saving my report in wireshark and starting sniffing...
