Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
We want to qualify a product with nrf52832 and preferable S132 6.1.1. When we tried to use QDID 125047 there were inconsistency problems in Launch Studio, table 1a was not...
Can i configure more than one pin for wake up the microcontroler from deep sleep ? like this: nrf_gpio_cfg_sense_input(30, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_LOW); nrf_gpio_cfg_sense_input...
What is the receive buffer size for IP packet data, i.e. how many bytes of data can the modem receive (in one or several UDP packets) before I call recv() or recvfrom() on...
Hi Sir,
For test the nRF9160 GPS, based on the nRF connect v1.2.0.
Do we have the GPS API for cold/warm/hot start?
And which example code we can reference?
Thank you...
Hi,
Recently I have been working on serial LTE modem code and it seems to work great for TCP and UDP. I am trying to enable GPS module by the command mentioned in this link...
Hi,
is the 100k pull-down on the COEX2 pin required as stated in the product specification ? I don't see it being followed anywhere (reference circuitry, nRF9160 DK schematic...
Hi,
I am developing nrf52832 on zephyr platform, I have seen a very useful GitHub library you guys have created called 'NordicPlayground' https://github.com/NordicPlayground...
How can I log on a router when a coordinator is in pairing mode, what I mean is that the coordinator sends a message so the routers know and set them selfs up on pairing mode...
For our nRF52832-QFAA design, we've just completed all tests according EN 300 328 (Radio). All but one test passed: spurious emissions at 4.9 GHz showed -44dBm, exceeding...
I use nRF52832 chip and SDK 15.3 version. I try to build nRF52 project with SDK 15.3.0. I spent a lot of time to fix a lot of issue in during compilation and linking. I used...
Hello,
I'm trying to build the HTS221 sensor example for nRF9160 but got this error :
I'm compiling the code with ncs v1.2.0 and here is my prj.conf :
Can someone...
Now I can only download the 《nRF52810 product brief.pdf》 . The link is shown below:
https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF52810/GetStarted...
Hi,
I am using nRF52832 for my project. I want to perform secure connection using numeric comparison.
I want to know how six digit passkey is generated by the softdevice...
Hi,
For the testing purpose, I would like to send a few basic packets from LTE Link Monitor on nRF9160 DK to our cloud. I found a way how to do it through the nRF9160: Serial...
Hello guys,
We are developing our IoT prototype with Thingy:91 board using v1.2.0 tag.
One of the things we need to to is as follows:
Scan the BLE area looking for...
