Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
We're porting an nRFS52832 app from an earlier version (14) to 15.2. Using sd_ble_gap_device_name_set( &secMode, dN, len ) with a string of length=9 will only show 5 chars...
Hi, we are trying to get the nRF9160 connected to the internet again, we had it working 6 months ago.
Our hardware is 0.8.5
We are in Ireland where we only have NB-IOT...
Hi
I'm using the watchdog of the nRF52832 Rev. 1.
The PS V1.4 states that the maximum run current of the watchdog is 2uA while the typical current is only 0.3uA. Can you...
Hi,
I am migrating from SDK14.2 to SDK15.0 and I can compile now, but when runnning the nrfx_uart_init the hardware handshake signal RTS is high from the beginning.
...
I am running into compile errors in different places in the SDK where there are lines as shown below: #if (NRF_BLE_GATT_ENABLED) /* do something */ #endif It is a widely and...
Hello Team,
Currently, we are evaluating nRF52 using nRF52840DK for one of our upcoming project. Basically, our typical application involves sending 32 Bytes of command...
I am using nRF52840dk SDK15.3.0 ble_app_att_mtu_throughput example,in that example i included some part of ble_app_uart code. Now the issue i am facing is ble_link_ctx_manager...
im trying to do notification for characteristic of a service whenever i trying to notify from nrf mobile app the debug session in ses is stopping its play in few seconds
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Assume I have one FDS record. With this...
Hello,
If I understand well the characteristics of the Thingy.91 si that you supplie a firmware we can download and modify as we want because it is open source, is that...
We're trying to diagnose an issue that's occurred to at least two of our customers. For some reason, we've found two different iPhones that are seeing our reader (nRF52840...
Hello,
Float printk (%f and %0.2f) is not working. I use newlib and activated floats for print and scan support without success.
Configuration:
Version from 31 january...
Hello!
I use nRF52-DK wuth android device. DK connects to android device and works with it well. But I want a paired DK make unpaired from android device by performing unpair...
Hi,
I have requirement of BLE node to node communication in mesh network.
All the nodes should have single firmware which will be capable of publishing and subscribing...
