According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
Good day!
Statement of porblem: We are developing appliction using nrf52832. In our application we have Capacitive touch button and capacitive wheel sensor for user...
Hi,
I am using bootloader and application based on SDK15.3.0 and SD s140_nrf52_6.1.1_softdevice.hex.
I am also using our own BLE transport layer in application to receive...
Hello, I can see in the datasheet of the NRF52840-CKAA-R that the recommanded inductor value for DCCH is 10uH +-10% (configuration no. 4). Unfortunately, we experience some...
Or may be another procedure to make a list of surrounding beacons nearby using nrf52832. We are beginners, sorry.
What do you recommend to start with?
Sdk16, 7.0.1 Softdevice...
Hi,
I have configured pin 10 (STATUS_BUTTON) on my own design board using a nRF52832 chop as follows:
I am intending to use the internal pull-up resistor to pull the...
Hi,
I'm trying to emulate a server device with pc-ble-driver-py, I recently moved from version 0.11.4 using Python 2.7.12 to version 0.14.0 using Python 3.7.4. I'm trying...
Hi,
I am using segger studio and NRF52810 for my development. I started with the NRF52 dev kit and complied with the sample app given in PCA10040e folder.
Now I want to...
Hi All,
I'm trying to figure out the best way to implement the security between two industrial IoT devices. We don't have a good out-of-band channel for more "traditional...
Hi,
I'm using Thingy:91 and I have built and flash the asset tracker software. I have connected the external GPS antenna (MIKE3A or similar), see picture.
How do I check...
I am using nrf52832 chip along with softdevice as a peripheral. There is a requirement wherein we want to encode the advertisement data.
Came across ble_advdata_encode(...
I'm reviewing the ringbuf library for use with FreeRTOS across two threads and I can't see how the atomic operations implemented in the library make it thread safe. The atomic...
My debug uart stopped working after creating overlay files to make port changing easier. Is this a known issue? They're still the same pins and baud rates.
Hi, I have done a project in my DK52 using the ble_app_uart as base program, it is working very good in my evaluation board but when I download the program to my final target...
Hello all,
LED3 from nRF9160 DK doesn't blink after I erase all with SES.
what I've done so far:
Update successfully the modem to 1.1.0
Load the applikation 'nRF9160_DK_board_controller_FW...
Hi,
Is it possible to list down all available device to my console using static provisioner code on nrf52840DK using bluetooth mesh stack?
Thanks for your valuable...
