nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi, I need to use whitelist in ble_app_uart example, What are the steps that need to be followed for that. Is device Manager is mandatory for using whitelist. Can anyone throw...
Hi all, i followed the tutorial " devzone.nordicsemi.com/.../" and did the challanges, however there is a detail i don't understand (totally newbie here!): the value of temperature...
Hi Nordic Community and Developers,
I'm designing a small Bluetooth module using nRF51822 to use it in my next projects and I need to use thinner substrate material (~0...
I have an application that we have ported to the nRF52 that used an EEPROM to manage configuration values. This application doesn't update these values often but when they...
Hi All, we have used Arduino modules based at 24L01+ in our application, now we are getting to apoint where we need to find one of theese or another one and do a redesign...
Hi, I'm searching platform for my project.
I will need to send packets from big quantity of transmitters (nRF24LE1) to one reciever (nRF24L01), it will something like voting...
Hi i am interfacing mma842with nrf51822. but i am not getting data. i have uploaded code. can you tell me what is problem. i don't know i am not getting who am i id try.r...
I've noticed that our custom board sometimes does not work (e.g. execute the code) when the VCC drops to about 0.3V- 0.5V and comes back on again to 3.3V.
For testing I...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
In SDK_v11.0.0-2.alpha, there is a project: examples\ble_peripheral\ble_app_hrs_freertos\pca10028\ble_app_hrs_freertos\s130_with_dfu_pca10028.
But I can't find DFU service...
to # einar thorsrud
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive...
Hi
I am writing an app to utilise the new LESC feature using Diffie Hellman related pairing. I am testing the app against the Nordic provided ble_app_multirole_lesc. I...
with SDK 10 I found 2 SPI libraries, spi_w5_master and nrf_driv_spi . I hesitate between them.
what' the difference between them? and what should I use when I'm using app_timer...
I saw this tutorial:
nRF51 current consumption guide
It's specifically directed to the nRF51, but I guess the principles of Tuning Advertising parameters must be general...
