Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi,
I am looking for an wearable solution which should be able to full duplex audio transfer over Bluetooth. Is this possible with BLE 4.1/4.2. As here battery life is...
Greetings. Could you provide more information on the issues with GPIO located near the radio in the nRF52 (PS 18.2.1)? Specifically, what is considered "high frequency digital...
I've created a BLE Peripheral project to test maximum possible throughput for the Notify of a single characteristic. I've also created a Central based on the new BLE Central...
Hi: I want use all eight ADC channel, But I don't know how to get different channel conversion result.
I write my code as follow:
void adc_config(void)
{
const...
Hi,
I'm using the 3rd generation of nRF51822 with S110 v8.0.0 and the SDK 10.0.
In my application i'm using the uart core to communicate with the external device.
I'm...
I'm not sure why I didn't notice this sooner.
When trying to do a bonded DFU with a Nexus 6P and Master Control Panel it seems to get stuck in a loop reconnecting.
I...
Hi I trying to connect Altimeter ( mpl 3115a2) to the nrf52 development kit. Can someone guide me how to do it (pin connection). I have followed the example given in the sdk...
I received my nRF51 DK (with nRF51422, PCA 10028) and I could successfully run the S130 demo app thats included with SDK 8.0.0.
The above demo demonstrates for e.g. :
...
I was upset early this afternoon because I was experiencing issues with buttonless DFU on Android. As is usually the case, I assumed it was my fault.
First, I reverted...
Hi Nordic--
Our custom nRF51822 design has 13 signals routed into the app_buttons module through the GPIO -> GPIOTE->PORT -> nrf_drv_gpiote.c -> app_buttons.c path. For...
Hi,
I have a problem to program an external board with my PCA10028 board. My external board is a Xuntong chip.
( Heart-Rate-Monitor-2-4GHz-SOC-BLE-Module-based-on-nRF51822...
I'm trying to measure absolute minimum power consumption of the chip using the PCA10028. I cut SB 9, and applied a very sensitive current measuring device to P22. I'm running...
