The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hello,
I'm currently working on a fitness tracker application using the Nordic nRF7002 DK board, paired with an analog MMA7361 accelerometer , and a round GC9A01 SPI-based...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
hi all
I designed this board. Could you please review it from a hardware perspective, especially regarding the nRF52840 microcontroller? Specifically, I would like feedback...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
Hello , I tried Integrating NINA-B41 ble module with STM32F412 series board , Ble module is communicated over uart through AT command , it is working fine
BUT When I send...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi, I am using an external host with NRF54l!5 dk to test the channel sounding feature.
Can you tell me how the NRF controller supports this Cs procedure and whether the...
Dear Sirs
I try to read SoftDevice version using
ble_version_t version; sd_ble_version_get(&version);
As I understand I get version of SoftDevice in field subversion_number...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
I followed the DevAcademy lesson on WiFi FOTA with AWS IoT, with some modifications to work with my board.
The device correctly connects to the AWS mqtt server and published...
