hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi everyone,
Where I can read transmission type and device number of connected ANT+ device (HRM)? I want save those values and bound later only with currently connected...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
I received a NRF_ERROR_INTERNAL error from a pstorage_store() function. As far as I can tell this error should not result from this function. It occurs fairly randomly. This...
In the examples delivered by Nordic, there is ble_app_hrs in ble_peripheral and ble_app_hrs_c in ble_central. But I cannot find a ble_app_hts_c in ble_central for the ble_perifpheral...
I am using Master Control Panel to check some off the shelf BLE product. I noticed that some of them don't provide characteristic value when I press "discover services". ...
I am using the "nRFgo SDK 2.3.0.10040".
The datasheet of 24LU1P says the size of the bootloader is 2K.
But when I build it in Keil, the build information is "Program...
Hello.
I am using a nrf51822 with sdk 10 and softdevice 130.
It has an accelerometer mma8653 to read the orientation of the chip, I am trying to get the x,y and z co-ordinates...
Hi there!
I have nRF51 DK (PCA10028).
I config GIPO as below:
nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrf_drv_gpiote_out_init...
Hi, I am generating PWM waves using GPIOTE, PPI and Timer. (I cannot use the app_pwm library from SDK 10.0 because there is an intial delay of ~600usec for the PWM to get...
