Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
Thanks for the info already provided in devzone.nordicsemi.com/.../
I'm starting a new design with size (and volume) minimization a key requirement. Couple questions: ...
I am looking at the common nRF24L01+ module PCB with integrated antenna which is available at several suppliers. See picture below:
My question is - was this PCB design...
I'm using nrf51822, sd 10 and bootlader from sdk10. I can perform DFU to my application by loading the zip file with nRF master control.
Now I performed some customizations...
Hi
nRF51 dongle is no response from master emulation. I already did erased and flashed again few times but still not resolve.
I'm also restart my PC as well but the...
Dear nordic.
I am testing with nRF51822,
and have some question about hardware stability check.
Could I check below hardware stability, during or after system initialization...
i using a ble_app_hrs_freertos example, nrf52
I inserted a new custom task.
if(pdPASS != xTaskCreate(main_thread, "MAIN", 32, NULL , 1, &m_main_thread))
{
APP_ERROR_HANDLER...
I am attempting to make the change to peer_manager, fromd evice manager, and the in ble_advertising_start()
pstorage_access_status_get() call, I'm not sure what to change...
I am testing the DTM mode on the nRF51822_QFAA, and I use the carrier-only test with the following command :
dtm_init();
dtm_cmd(LE_TRANSMITTER_TEST, 39, CARRIER_TEST...
