I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
Hi,
I am evaluating the NRF52 with PCA10040 board and nRF5x_SDK_11.0.0.alpha.
I want to create Wave Forme as below.
Out[0] pin transit low to high at compare 0, Out...
I noticed S110 is not listed as supported by nRF5 SDK11. However, no supported SoftDevice seems to offer the same functionality as the S110 (Peripheral only protocol stack...
Hi,
in SDK v9, i tried to compile the bootloader example, but:
/usr/lib/gcc/arm-none-eabi/5.3.0/../../../../arm-none-eabi/bin/ld: region `FLASH' overflowed by 6944 bytes...
Did anybody know how I could determine the connection interval for a established ble connection between an android (4.4) central and a (e.g. nRF51822) peripheral?
I've been having a little bit of an issue trying to parse UART data that I am receiving from an external device.
Where I'm having issues right now is comparing an incoming...
Every 10 packets send; it will have at least 1 packet with 1-2 bytes corrupted data.
The configuration as below:
data rate: 2Mbps
channel: 7
Prefix0: 0xE2
BASE0...
Hi,
We have an application that can run in two modes. The mode is selected by setting the GPREGRET to 1 or 0 and restarting.
Currently we are running this procedure directly...
Hi,
We are developing a product using the nrf 51422 where the power source is a 3 phase generator.
We rectify and charge on a supercap where the uProc is being supplied...
Please correct me if I'm wrong but my understanding is that unused RAM banks can be disabled to reduce quiescent current.
My first question is what is the current consumption...
Hi,
I'm using RTT debugging with soft-device " https://devzone.nordicsemi.com/tutorials/6/debugging-with-real-time-terminal/ " , I'm able to print few messages, after which...
Hi~ I'm sorry because it usually does not use English writing in English, So there may be errors in English please forgive me.
Last year, I bought some nRF51 Development...
Short: Working Timer. Working SPI. SPI does not work when triggered by timer_handler.
Hello,
I am currently trying to replace delays with timer in my code...
I set...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I want to make nRF51 goes sleep mode.
So I tested linked source code as below.
github.com/.../main.c
It works well.
But...
