Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I want to connect Bluetooth Smart chip to a weighting scale, read the data and send it to a phone.
Is this possible and what requirements there are for the scale?
The Manual of the nRF518-SDK version 5.1.0 mentions something called nrfprog. Unfortunately the SDK doesn't include it. Unlike what i found on google, i see no nrfprog in...
I have an nRF51822 design that programs fine from the embedded Segger on the eval board.
However, when I try to connect an actual J-Link Base, I can't seem to get it to...
Hi
I have PCA10005 module disassembled from mother board and with VCC_nrf, GND connected to external supply. The chip is able to work with pre-programmed data.
Is anyone...
Hi,
i have a generell question. First i have to say i am not the best programmer, but maybe some one with more experience then me could help me.
Does it make sense to...
Got nRF51422-EK.
Followed instructions and used nRF51 SDK v6.1.0
LED next to the Segger part blinks constantly.
If i build and download Blinky, the LED0/1 do not alternate...
I am developing a platform using C8051F931, MPU9150 and nRF8001. I have re-written the hal code to target the C8051F931 and verified it using the ACI demo test (the echo test...
Hi,
I'm using nrf51822, pca10001 board. I have loaded the uart_example and that worked fine, but using the radio_test_example from Board/nrf6310, that compiled and programmed...
Hello,
I'm new to BLE. I am using nRF51822. Is it possible to modify calling frequency of nus_data_handler() so that I can deal with data coming from BLE faster?
How can...
I see that Digi-Key has two part numbers for the nRF51422-QFAA:
But I don't see any reference to "V2" part number field in the nRF51422-PS document.
What is the exact...
Currently I am set timeout to one second and then on BLE_GAP_EVT_TIMEOUT:
modify data
advertising_init();
advertising_start();
Are there more correct ways...
Hello,
I've connected the nRF8001 module and a light sensor to a microcontroller.
Actually I can read data only when I send a string from my smartphone but I want to...
I'm able to program the Soft Device (s110_nrf51822_7.1.0_softdevice.hex) from nRFGo studio and the compare is fine, but when I go to Keil uVision 5, I can build ble_app_beacon...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
