Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
I have found the bellowing code which was in s130/ble_gatts_struct_seriallization.c of nRF51_SDK_10.0.0 : ( ble_gatts_attr_md_enc)
/* serializer does not support attributes...
I have two device , one is Tx-Device the other is Rx-Device.
Tx-Device : Auto continued Send 4 bytes data to Rx-Device by Radio.
Rx-Device : Using Radio Interrupt receive...
First of all I'm a BLE novice, so sorry if I'm asking obvious questions. I've built a home project where a battery powered mcu listens for requests over wifi and drives a...
Hello.
I'm trying to do as follows: ONE button used either to wakeup or to put system to sleep. In general almost everything is working but I cannot find how to configure...
HI,ALL
as i known, the BLE key is a six digit pin.
and in the static void device_manager_init(bool erase_bonds) ,the statement shows below:
register_param.sec_param...
According to this post , and this GitHub source file , in the nRF51 chip's mbed implementation:
The ADC reference voltage is 1/3 power supply
read_u16() seems to...
HI,ALL
in the nRF5_SDK_11.0.0-2.alpha_bc3f6a0 , GATT Server Event IDs.
i do not find the read event.
All i found is the BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST .
Now...
Hi, all
Recently I use nrf51822 CEAA, WLCSP package to develop a project on UV (ultraviolet), the UV sensor must be exposed to the sunlight. When we take the product board...
I'm running the DFU example from the nRF5110.0.0 SDK. dfu_dual_bank_ble_s110_pca10028 on the DK and it works perfectly using Master Control Panel, but it does not work from...
I currently have a dualbank bootloader setup and I'm trying to change it to singlebank. If I burn the singlebank bootloader with the jlink it works fine, but if I use the...
Hello,
I modified ble_nus_c to manage multiple connections.
The first time (first client) i call sd_ble_uuid_vs_add in init, it returns OK. The second time ERR_NO_MEM...
both for APP_UART_FIFO_INIT and APP_UART_INIT i never receive APP_UART_DATA_READY
but at least i get APP_UART_DATA sometimes .
most of the times i get APP_UART_COMMUNICATION_ERROR...
I'm trying to monitor the time a signal is high/low on a GPIO. It seems to work alright with timers and PPI, but I wish there was a way to reset the timer upon capture.
...
Hi,
What is the largest possible value of "MAX_VAL" for application timer given below:
"#define APP_TIMER_PRESCALER 0"
"#define M_DELAY APP_TIMER_TICKS(MAX_VAL, APP_TIMER_PRESCALER...
