Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
i'm working on nRF51422 and i'm trying to do a simple BLE object that advertise his name and his services and is connectable by the others.
Advertising and connecting...
Hello,
I am working with nRF51422 & would like to know if I can measure current of single event & multiple events (pictures attached) as detailed as possible. I have cut...
Hello everyone.
I want to increase the operating range for nRF51822. To do this I added PA SE2576L in design.
Unfortunately, I do not have experience in RF develop...
Hi,
I'm attempting to use Version 2.1.0 of the HomeKit SDK on an nRF52. We're using the s132 SoftDevice 2.0.0-7.alpha (the SoftDevice in the latest nRF5 SDK v11.0.0). ...
Hi.
So my problem is, that i cannot successfully program external board with preprogrammed nrf51822 chip in the board.. This board is from china.. its an ibeacon.. If i...
I've recently been playing around with Bluetooth Developer Studio, and I can see it's potential despite it having a few annoying bugs.
I've set up a custom service by re...
Where would be a good place to feed a watchdog when using a softdevice?
My first guess was in main loop:
for (;;) {
NRF_WDT->RR[RR_number] = 0x6E524635;
power_manage...
Hi,
When a watch dog timeout occurs, I want to save some data to the flash memory prior to reset (namely the RTC count value). Therefore I enabled the wdt interrupt. The...
Im using nrf51, I configured the watchdog to reset after 3 seconds of hang and it works. But I have absolutely to save some data in flash before reset
Is there anyway to...
My custom profile was being built fine until I added a couple of standard descriptors to a custom service characteristic. Any idea what's going on here?
19:34 - [Code Generator...
Hello All,
I want to develop bluetooth mesh using NRF51.
I have question about this:
Is their library closed or not?
Do we need smartphone like in CSR?
...
Hi, I have a TinyShield Nordic module and I am having some troubles trying to customize the advertising packet. I have downloaded NRFGO Studio and I have enabled service data...
I have an nRF 52 dev kit, an Asus router running openWRT, and an android phone with the master control panel.
I'm able to compile and flash the dev kit with the example...
hello,
I am using the nrf51822, I want to add a normal service which do not need bond before used at the ancs example.I hope it can do the follow tow points,firstly,if the...
Hi,
I tried to figure out what is happening on the lower Bluetooth levels but it is very difficult to find straightforward information. Especially the Bluetooth (4.2) standard...
