I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I am curious to know what is the interpretation for the advertisement data
Advertising Data: 0201050709506562626c6503190002
This advertisement data seems to...
Hi,
Our custom board stops working after updating the connection parameters. We have a nrf51822 chipset custom board with proximity application flashed on it. Device get...
Dear Sir,
I open the Master Control Panel log.txt file, I can see
Serial port read: 04-3E-13-01-00-00-00-00 and
Serial port write: 02-00-00-09
Where can find the full...
I am using a nRF51822 at 16 MHz
What is the math formula behind the BAUDRATE register?
What is the timing error for each of the standard baud rate setting? This is not...
hello,
i was trying to run the sample examples, i tried blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. i was succesfull in getting the...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
Hi,
I need to drive a piezo buzzer. Just need to make a simple beep function(s) that one call will start generating a specified frequency on specified pin and other call...
there is no sample code in nrf5188 sdk to use BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM,
what's the difference between the two settings?
for BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM...
Hi,
I am using IAR Workbench for ARM to develop my application and I'm experiencing a very frustrating issue with my debugger (J-Link that came with the development kit)...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
