Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Using VS Code and latest version of SDK and toolchains. I have created some custom board definitions and placed them in a seperate directory. The directory is registered in...
Hi!
I faced an issue with nRF Cloud Log. If I set CONFIG_LOG_TIMESTAMP_USE_REALTIME=y, I get wrong timestamps (2080 year..) in nRF Cloud Portal for all messages being...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
I'm trying to get a basic CI/CD pipeline working in Azure DevOps, using Azure hosted agents, and I'm running into a problem where West is silently failing to clone the project...
Hello All,
In past we have used nRF Connect SDK 2.0.0 for ZigBee and made a FW, during which one of my co-worker had changed few of the SDK files also.
Now we would like...
Hi,
on a Mac, I am trying to install credentials to a nRF9160 using device_credentials_installer.py.
The nRF9160 is running the AT Host application. I can connect to it...
Hello,
I am developing an application using nRF52840 with the NRF Connect SDK version 2.4.0 based on Matter: Template sample and I configured 10 buttons interrupts successfully...
Hello team,
We are in the process of migrating from the nRF5 SDK to the nRF Connect SDK for our upcoming projects.
We have followed all the official setup and installation...
Hello, We have created a new product with the nRF52805 "Raytac" Module under nrf5 SDK v17.0.2. We are planning to do the CE certification soon. would like to verify a few...
Hi,
Tried to use Connectivity bridge app on a custom board based on NRF52840 and it seems that the UART-USB interface works initially, but after a while it gets stuck at...
Hi,
We are evaluating the Thingy:91x and found that the BLE range is significantly decreased compared to the Thingy:91. The nRF5340 has a lower maximum TX power but when...
Hi,
1.How should nRF21540 be added to the nRF52840 DK ncp example? Please provide the lines of code that need to be modified. 2. How should the uart interface be modified...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hi,
I have a question about creating a custom board. I am following the tutorial here: youtube
I am trying to make a custom board for nRF54L15 using the board wizard ...
