Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello,
I am using SPI interface to communicate with a sensor BMI160, looking into the driver for BMI160 I can see how the low level functions for reading/writting are used...
Hi,
i am trying to upload the code to BLE 400 from waveshare from nrfGo by getting the hex file from this library
While Trying to upload the code i am getting the following...
onkey_full_20170814.hex
onkey_0000.hex
onkey_boot_s132.hex
This time 14.0 sdk was updated.
There was a problem after the update
Problems when uploading bootloader...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51 controller.
I am using muliple nrf51 devices to connect each other and share sensor data with each...
I'm using a pin for trigger switch input with the following codes
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;...
Hi,
I would like send serial data in both directions (like by RS-232) between BMD-300 Evaluation Kit and BLED112 dongle.
I'm a beginner on this subject, so I'll ask...
Hi,
i am working on custom nrf52 board which is operating by Li battery of 3.7v 27mAh battery. now the battery is dead i didnt find 27mAh batteries in the market near to...
Hello there,
I am working with a peripheral device that we are testing with many different devices, and have run into a very unusual issue. With a brand new Android tablet...
Hii all,
I'm working on a project that device will have both central and peripheral capabilities so we are using s130. I tested my application with 2 central links and...
I have installed and un-installed all the required components to run the dev kit with eclipse. As everyone knows this is complicated because there are multiple sources of...
Hello!
I'm from a small company located in Austria. We are in the smart lock business and at the moment working on passing the CE certification with our newest hardware...
Hello All,
I am designing one custom board where i want to Handle the LEDS, Like in Nrf51DK when we connect through UART_APP from smartphone blinking LED1 on DK gets constant...
Hello,
I have a project in witch I want to send the data received from an Arduino by UART, this data has a size of a little bit less than 80 bytes, this data is received...
