Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Hi,
I am using "nrf5 sdk v11.0" example "ble_ancs_c" for nrf52_DK(PCA10040) .
when i connect to the nrf_device from ios device i am able to pair and connect to ancs client...
Hi,
I'm using the example nRF5_SDK_11/examples/ble_peripheral/ble_app_uart witn a pc10028 board. The central is done on a linux machine with a python program under bluepy...
Hi,
We would like to use the nRF52 in the following way:
BLE communication via S132
button / IRQ to wakeup nRF52 application
put nRF52 to sleep after BLE communication...
As we known,RSSI means Received Signal Strength Indicator,TXPOWER decide the power of output port.How do the two factors combine affect the device work?
Hi I spent a few days on trying to setup a thread external commissioner using Nordic nRF52840 and RaspPi 3 as a border router.
First I realized that border router implementation...
Hi
I'm having major problems implementing current time service client (cts_c). I've run ble_app_cts_c on my device and it works fine. I copied the relevant parts of the...
Bluetooth SIG recently released BLE Mesh standard 1.0. Is nordic mesh compatible with the new released SIG standard?
If not when is it planning to release a SIG compatible...
Hello,
I did used nrf_drv_spis.c (SDK SPI Slave) with nrf_drv_spi.c (SDK SPI Master). And I notice that both module configure SPI MISO line as input without any pull (neither...
Hello,
I am using nrf52832 DK and I would like to use the GPIOs port to debug a couple of signals that I genereate within the MCU.
So far I have configured my GPIOTE...
Dear experts,
I've been playing around with Thread since nRF5 SDK for Thread v0.8.0, cloud_coap_client.
I use your Border Router example with NCP example running on nRF52840_Preview_DevKit...
Hi:
I got an 0x04 no mem error with sd_ble_enable.
But my hardware worked just fine before, so after some tussle I found out that the sd_ble_enable of my working program...
how to set the ble stack ,let the sd_ble_gatts_hvx() send data return more fast,now from i use sd_ble_gatts_hvx() to get the return (BLE_TX_COMPLETE) needed 300ms.
Dear Nordic Team,
Thanks for supporting.
Anybody work with ultrasonic sensor (HC-04). Please guide me. I am just interface with arduino example its working good. It...
Hi all,
I'm completely new to wireless connectivity development and I am looking to use a nRF52832 module for simply communicating button presses between a power optimized...
