Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hello,
I am trying to understand how to appropriately handle the Device Manager event of DM_EVT_SECURITY_SETUP_REFRESH as a peripheral.
This occurs when the user loses...
Hi, I wanted o increase the frequency at which heart rate is updated.
So I made the following change
#define HEART_RATE_MEAS_INTERVAL APP_TIMER_TICKS(300, APP_TIMER_PRESCALER...
Hey guys!
I am using your spi-master driver from the SDK 11 with the nRF52 chip. I am trying to read data from a MPU-9250 chip, and through my logic analysis, it seems...
Hi to all!
I've developed a board with NRF8001 on it and it works fine. But I've noticed a strange behavior. I use a mobile phone with NRF master control panel to work...
Dear All,
I am making IR transmitter using nrf51 where IR codes saved in SD card using PWM library we can transmitt the code while BLE is working.
Is it possible that...
Hi,
I am working on some application in which i have combined multiple profiles in one code.
In this i don't want generic access and generic attribute profiles to be displayed...
Hello.
I am using RTT successfully with nrf52 and IAR. But the start address for the RTT control block is a moving target: it changes whenever my code changes. I want to...
The product specifications publication for the nRF51822 doesn't list a gull wing chip pinouts found on the PCA10028 found on the evaluation board, kinda wondering if there...
Can someone confirm that all that needs to be changed to make code run with the SD installed is to change the linker to link to 0x1C000 instead of 0x00000 ?
To test, I...
I am playing with nrf51 DK. I used the following sample code,
devzone.nordicsemi.com/.../
ble_app_template_with_pstorage_SDK_8_1_0.zip
I want to pstorage clear/store...
I'm having an issue with secure BLE pairing, and once the problem shows up, it will not go away until I reprogram the SoftDevice. It persists through resets, so it must be...
I am currently using the nrf52 device for an application where when user's of my devices come close to one another, they automatically start sharing state information. There...
Hello all,
I currently have a test rig with 3 sensors, each with their own pin and interrupt they are supposed to carry out. Whichever two I put first in my gpiote_init...
Dear all,
I'm using SDk130 and the Software is based on the ble_app_uart_c example.
Now I want to scan the advertising data from a peripheral (device name, peer address...
