Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello,
the available QDID for nRF52x refers to Softdevice which has no IoT capability, being this a work in progress.
When this will be ready, will Nordic release a new...
Hi,
I want to use the NRF51822 without the Bluetooth functionality. Is it possible to leave the pins ANT1, ANT2 and VDD_PA unconnected? If no, what is the cheapest way...
Hi,
I'm using PCA10040 board, There i connected the fuel gauge IC via TWI communication.
There pca10040 will acts as master and fuel gauge IC will acts as slave.
While...
Hi! I want to send data from the temperature sensor of the beacon, receive them with the nrf51 and then send them to the PC via USB cable. The nrf51 has to start the connection...
I am using the nrf51822 and I want to use the pstorage library to save some data which is "power lost can save",but I cloud not find the example of it.I am using the SDK 8...
Hi,
I want to have a generic fault handler that will cause a reset. The handler may be called from a high-priority ISR or exception trap (e.g. hard fault handler), and...
Is it possible to make a services like this：
services UUID : 55550001-5555-5555-5555-55555555555
characteristic UUID : 55550001-4444-4444-4444-444444444444
Hi All ,
I am using NRF52 , S132 softdevice ............
I need to read a data every 5s (In Timer1 interrupt handler) from I2C slave and sent it via BLE.
But what...
Hello,
How do I create an encrypted/signed image? Where can I find the documentation for doing this? How will I need to modify the bootloader to decode and install the...
Hi All,
I am using Nordic SDK version nrf51_SDK_9.0.0 for PCA10028 board. In that i am using application
D:\nRF51_SDK_9.0.0_2e23562\examples\ble_central_and_peripheral...
Hello Everyone,
I have developed my software and i have tested with NRF51DK using android phone NRF MASTER CONTROL PANEL APP and it is working very well but now am trying...
Hi Nordic,
On SDK10.0 with QFACA nrf51, I find a GPIOTE problem.
With sdk6.1 and app_gpiote module, I got no such problem.
I make use of SPI0,low accuracy GPIOTE on 4...
