I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hi
During schematic design, i read regarding proper powering of NRF52 (the product is battery powered 2xAAA). somehow i can't find this info now and i would like to verify...
What does mask and 1<< mean in the following code:
#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
...
Hi all,
I'm transferring data to and from an Atmel AT25040 NVRAM using SPI, and it works perfectly when run within main(). However, if I run the same code from within an...
Hi, I want to enable notification for a specific characteristic, and to do that, I must write 0x01 (in java it's going to be "01,00" ) to the CCCD handle of this characteristic...
Hi,
I tried to use python API to drive the nrf sniffer to capture ble device information by their advertisement packet. I can successfully target a specific ble device...
Hi, I'm wondering how much i need the LF crystal oscillator.
In this case, the chip is never asleep, in constant latency mode, and is constantly advertising and meshing...
Hey guys,
We have several different devices that use the nRF51822 and some using the nRF24L01. We currently use the proprietary RF protocol and have all of our devices successfully...
Hi,
Reading from flash, an already programmed key, returns zero.
Using sdk 12.1, sd s132_nrf52_3.0.0, nrf52832, and pstorage. The key is programmed after uploading the...
On nRF52 interrupts for GPIOTE, I need to perform one event when a button is pushed, and perform another different event when the button is released.
I've checked these...
When the PPK calibrates and turns off the DUT, does the nRF52832 on the PPK disconnect from the External DUT lines? My DUT has a LOT of capacitance on it, and it takes several...
Hello i use the example ble_app_beacon_s130_pca10028, i'll try to add UART functions, but they not work anybody has this problem, please help me!!
int main(void)
{
uint32_t...
Hi..! Friends..!
I am trying to detect the number of steps on accelerometer.
For which I want to Plot the accelerometer values in real time (with minimum rate 50values/sec...
I would like write music box by buzzer. So I need adjust the PWM frequency continuously.
But i don't find the sample cede which is about adjust PWM frequency in SDK.
Where...
