Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Thats the problem.
On Windows7, 64 bit, with the Bluetooth Stack from the USB BLE-Stick happens the following:
Windows (master) initiates the connection, sends a security...
Hi, I'm using nrf51822 and using SDK12.3 ble_app_uart.
My purpose is sending data using BLE module like this:
Custom Board -> BLE Module -> Android Phone.
It works...
Hi,
I am using 2 nrf51822 devices. one is central and other one is peripheral. I am using s130 softdevice.
When i was trying to connect NRF51822 to other nrf51822.
i tried...
Hello All,
I am working on nrf52840 trying DFU OTA by following steps provided in this link github.com/.../ota-prog.md . where they have mentioned to install python all...
Hi Nordic,
I've used a GPIO of the NRF52832 to drive a FET circuit which latches off the battery, however as the board voltage collapses I see a short pulse on the GPIO...
In single bank mode, need upgrade bootloader by DFU. Performing below procedure, APK shows "transfer complete". Application on target device is disappeared, but bootloader...
Why does the nrf connect app on Android need my location services enabled for it to work? I believe that is the case for most (or all) of the nrf apps in Android.
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12.
...
I've read as many posts regarding changing the ble connection interval as I can find but so far have been unsuccessful changing the ble connection interval.
Below has been...
Hi all,
Does in any chip with some constellation (different SD) the device allows less than 7.5ms for the connection interval? Or is this value the absolute minimum?
I am trying to connect to a peripheral device advertising f0000000-0114-4000-B000-000000000000 as the UUID. The peripheral adds it to the stack via sd_ble_uuid_vs_add after...
Hi,
I am using ESB in one of our current projects. I have two devices: one PTX (master) and one PRX (slave). The slave may want to send some data to the master from time...
We have an nRF52832 and an MSP430 on a custom board. We would like to program both the devices using SWD interface.
Would it be possible that both these devices can share...
Hi,
I have an nrf51822 ( variant AB) and I am trying to program a simple ble app beacon example on it.
But I am failing over and over. After searching , I found out that...
Hi,
I am using pca10040 board with s132 softdevice. I have integrated BLE_APP_UART service with BLE_APP_MULTIROLE_LESC example. The device will start advertising when command...
