Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Good morning,
Some contextualization first:
At my company we developed a product that is based on your NRF52832 microcontroller.
We are currently entering the certification...
I am encountering some problem in building eclipse project following the tutorial at devzone.nordicsemi.com/.../ .
Previously I succeeded in building with another simple...
Hi,
We bought several nRF52 DK with nrf52832 and intention is configure one of these as a gateway router to cloud via Rasberry PI.
I have IAR installed and I tested blinky...
Hello,
I've been all over the forum trying to solve my problem but I just couldn't find enough information.
I'm trying to set up notifications in my application, but...
Hello,
We're using SDK v14 and nRF52. To pass some data between reboots we're using the general purpose retention register. However, it seems like it's impossible to call...
I try to transfer the codewords from nrf51822 Dk board to a dongle board, while the dk board is PCA10028 and the dongle board is PCA10031, when I change the port numbers and...
I'm new to the nrf51822, i was connected led to one of the gpio pin of nrf51822 development board. In 1 minite i want to toggle led 20sec and remaining 40 sec in sleep. After...
The SDK 12.1.0 documentation for the FDS library says the following:
FDS_THREADS: If set, the FDS module can be used by multiple modules at the same time (for example...
Hello,
I am trying to measure the current consumption.
i could cut the SB9.
and i use analog discovery and measured!!
the picture is shown in below.
gyazo.com/b9f5607148cd9415ea7d1ee6ac644373...
Hi
I have tried to make use of the FDS for storing data and encountered this behaviour.
The required setup of the sys_evt_dispatch() & fs_sys_event_handler(sys_evt) are...
Hi,
were are looking forward to redesign our PCB. The nRF51822 will communicate via I2C which sinks up to 3 mA and 15 IOs will source the maximum rate of 15mA. Additional...
Hello,
I implemented a function to add characteristics to a service, but I'm having a problem when I add notifiable characteristics. I pass a set of flags to my function...
Hi,
I set a debug LED on as the very first thing I do in main. Randomly (sometimes 2 in a row, sometimes 1 in 100), sometimes my debug LED never comes on and no code is executed...
Hey Everyone,
I am new to nordic development. I am really used to programming with easy environments like the Arduino. I have seen some examples using the printf() command...
Use the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_library routines, now can output two lines of PWM, but want to two way different PWM phase have...
