Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
Iam a beginner to NRF51 and Iot.
I want to be able to send messages from raspberry pie to NRF51 dk and vice versa via Bluetooth.
Iam using a generic Bluetooth dongle...
Hi ,
I've just started using a Nordic's product : an nRF51 422 QFAC develepement Kit
I was running tests by loading examples on this board when I lost the connection between...
I am building my application up on the blinky free rtos. I want to use RTC and ble stack. i am initialising RTC1 first and ble stack stact.
The problem is that I am getting...
I am using nordic nrf8002 BLE with a breakout board & not a developement kit. I gave 3.3v supply in different combinations:
(1)3.3v to vdd pin-1, GND to vss pin-4
(2)3.3v...
Is any SDK available which has single bank BLE DFU bootloader source code?
If No then is it possible to convert dual bank BLE dfu bootloader into single bank BLE dfu bootloader...
I am trying to Migrate from Sdk 6 to Sdk 11 .
Here i am facing problem in discovering Custom Characteristics .
I can successfully add service and 2 characteristics without...
Hi!
I'm building an application with one custom service containing a few characteristics, all of which are to be indicated upon. When using the Master Control Panel Android...
How can I calculate the maximum throughput for an application running on the nRF51822 and the S110, when connecting to different kind of Central devices?
If we want to obtain sets of five "Bluetooth stylish temperature sensors, do you have a selling point in The Netherlands? If not maybe a way to obtain this by mail or parcel...
Hi!
I am coding soft for nRF52xx. Having looked through the examples I've got one question.
In the preprocessor defined:
NRF52_PAN_24
NRF52_PAN_25
NRF52_PAN_26
NRF52_PAN_27...
We have a nrf51822 chip connected to an arduino-like device. We need to use UART for communication, but without firmware modification the master chip doesn't support USART...
Hi.
I'm using PCA10028, SDK10.0.0, S130. I'm a beginner.
If I want to download hex files(soft device and fw code) though UART port, is it possible?
If possible, could you...
Dear all,
I checked the SDK release note and found Nordic decide not to support CMSIS anymore.
As I developing with 52832, I try to use FreeRtos to control the whole system...
Hi: I want use freeRTOS on nrf51822 based on sdk10. But when I open the example project"blinky_freertos"and try to use it, The keil5 manage run-time environment tell me "install...
