Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
Hi Nordic team,
I'm using the nRF5340 + nRF7002 to securely connect to my backend over HTTPS using Wi-Fi and the native TLS support (mbedTLS).
What works:
I can...
Hi, recently I have been experimenting with the channel sounding with range requestor sample on the nrf54l15dk. I have modified the reflector code to make it connect with...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
I have a few characteristics under a service, and I'm trying to store the value if any of these characteristics is written to. However I run into an issue where if I enable...
Hi !
There is one thing I don't understand with the led included on the NRF51-DK board.
According to this thread ( devzone.nordicsemi.com/.../ and the datasheet it seems...
I want to take saadc samples for one second,every 5 seconds,the rest of the time the mcu is in system on sleep mode with rtc1 on.Eery 5 second there is an rtc event and the...
As the datasheet showing
The GPIOTE input mode consumpt upto 22uA ,it is inconceivable.I want use NRF51822 to design a ultra low power consumption production ,and use...
HI:
I want to use nRF24L01+ as TX, and nRF51 Dongle as RX. And I try to use nRF51 Dongle to just listen for the RSSI of the NRF24L01+. Is there any example or reference...
Hi, I am new to nRF51DK. I am following this tutorial shown below:
developer.nordicsemi.com/.../a00066.html
After I flash my s130 softdevice, I follow the file directories...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
Hi, i am designing a board using balun in it. Also, i am going to use meander antenna of nordic dongle(reference image is attached). As i can see, there is no RF coplaner...
Hello , I want know , if i used the Gazell Pairing Library (gzp) , it means that I can not use the ACK
Payload function ？if i can use the ack payload function place give...
Hi,
after reading the NFC with an smartphone the power consumption stays very high without doing anything else...
I don't know if this is related to this bug: "NFCT...
Hi,
I saw in the infocenter that the SAADC can measure the VDD directly. So in my case I want to check the voltage of a 3.3v coin cell regularly, I could do this without...
Hi Everyone,
The On Semi 7150SL reference design incorporates a dongle that can stream stereo music to two hearing aids which are equipped with the Ezairo 7150 module....
Dear sir,
Can we use NRF51822 OR NRF52832 as a slave device .As our controller is STM32F407ZET6 and we did not want to change any firmware from our previous version except...
