Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
I'm Dinesh Katkar, trying to adapt
new IoT design and development and planning to build wearable device based on nRF52832 Bluetooth SoC chip and ordered nRF52 Development...
Hello,
I am new to all this RF stuff. I am trying to set up multiple transmitters (2 for now) and one receiver. Basically, each of two transmitters read one set of data ...
hi all,
i am currently using version 8 sdk.
i tried to include bsp_init() function in my code.
i attached following header files
#include "nrf51.h"
#include <stdbool...
When exporting the example project BLE_HeartRate from the online IDE to the GCC (ARM Embedded) toolchain, the makefile fails to compile.
First, the compiler throws "fatal...
Hi:
I am using nRF51 Dongle to develop my platform, and software is base on esb_low_power_prx and esb_low_power_ptx in nRF5_SDK_V11.
For production, I need to program...
When I connect to another beacon using sd_ble_gap_connect() scanning on my device is stopped. I have to wait till connection is established or establishing connection fails...
The Nordic set comes with a Device number of it's own. I want to overwrite that device number, or store a device number in a different location in the EEPROM. Is there any...
What files within the FDS are used by the modules of the Nordic SDK?
For example, I know that the Peer Manager uses the FDS as a storage backend. I need to know what files...
Previously I implemented a DFU bootloader. It works fine on s120 softdevice.
But after I ported it to s110 v7.0 softdevice, it can not work. After investigation, I found...
Hi,
i just followed the steps for migrating to peer_manager - as lines out in the tutorial.
However i will never ever get a callback to pm_evt_handler.
I am trying...
Hi,
I am facing some issues on the Android part of the BLE.
Firstly it takes around 20 seconds for the android phone in scanning mode to find the nordic board. This...
I encountered the following error while adding device manager to ble_uart_app in SDK_11 s130 using the hardware nrf51-DK. I'm using Keil compiler.
._build\nrf51422_xxac_s130...
While using the device manager, I encountered this line;
#define SEC_PARAM_MITM 1 /**< Man In The Middle protection not required. */
Since security is important, is...
