I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
hi,
i try to analyze the sdk sample with the standard(Server) ,ie : basic battery service
how to build GATT Requirements and Service Characteristics with the...
Just got the RF51822 PCA 1001 dev board and followed the instructions in SDK 4.4.1 and downloaded the Keil Lite tools from the ARM website.
BUT, didn't realize Keil has...
Hi,
how do I evoke Gazelle on NRF51422? According to specs NRF51422 supports both ANT and Gazelle although on SDK for 51422 the gzll folder is missing. It is present though...
Hi ,
I am using PCA10001 board.
Now i want create 4k buffer in RAM. Which is good way allocate memory to 4k buffer.
Can i use dynamic(malloc function) or static memory...
Assuming the system is composed of one device using nRF51822 and iPhone/PC,
If we want nRF51822 detectable by iPhone/PC so that iPhone/PC can connect nRF51822 when they want...
Hi!
I have been using Bluetooth 2.0 modules for years and now I want to take the step to 4.0/BLE. Previously I used Free2move modules with built in stack. Very simple, make...
I have the nRF51822 development kit (with the new hardware revision QFAA or something), and I am using the Master Control Panel with the new 0.9 firmware for the dongle. ...
Hi in my case,
i pressed gpio button for one time it will do one event.
and for double press it will do another event . how can i do this one,
Regards
Balaji
Hi
In my case i have both 3 gpio interrupts and 4 rtc1 interrupts and have some timer 0 and 1 interrupts
also. how to set priority for all these interrupts in both while...
Hi Guys,
I am planning on using the nrf24l01+ to send data with a payload which is larger than 32 bytes, I was wondering whats the fastest way to transmit these packets...
Hi,
In the nrf51822 SDK examples, there is an example of radio_example which is used for send data and read data. I want to konw that if one module send data and then...
Hello - I am trying to port code over from a development kit over to the WLCSP nRF51822 on a custom PCB.
I am able to connect/bond with my device fine, however I am having...
Hi,
we're using an nRF8001.
Trying to find the relevant Bluetooth Specifications, we found the following mess (pardon my french!):
Core Specification 4.0, 2300 pages...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
