Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
I have clone nRF51 mesh project(nRF51-ble-bcast-mesh-master.zip), and I can find BLE_gateway sample project in the zip file, but I can't find a led_mesh project. Does anybody...
In SDK 11, there was an immensely useful function known as NRF_LOG_PRINTF. in SDK 12, this seems to have been replaced by NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR. However...
pin 2 is for turning on and off at sepecified time...
pin 3 is for turning on the light whrn button is pressed and turned off automatically as time decided in the program...
I have been debugging this problem for a few days and have exhausted all of my options. I am relatively new to embedded development so user error is not out of the question...
Hi,
I need to load ble code to mrf51422. I read on the forum that I can do it using nrf51 dk but did not get the steps. Couod someone give me detailed description about...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello to everyone!
I'm digging documentation of SDK. and I meet a lot of doxygen things like this
/**@brief Macro for configuring a pin to use a GPIO IN or PORT EVENT...
Hello Everyone,
I want to program the BMD-300 with the nRF52 Preview Development Kit.
I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
...
Sorry for probably stupid question..
All the time in SDK we set need bits through the mask, for example
NRF_GPIOTE->CONFIG[idx] |= (pin << GPIOTE_CONFIG_PSEL_Pos) &...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
Hello,
i am new to BLE,
I am using the iot S1xx Softdevice on the nrf51 Dk in order to test ipv6 connection, and now i want to add advertising with the Eddystone protocol...
Sorry I am new to this. Therefore this question may seem to be odd:
I want to build a temp monitor using an nRF8001 (BLE Board Adafruit) and send this data to my mobile...
This is the code I am using to wakeup my system from OFF. It is not working. Kindly Help.
#define Pin_0 0
static void gpio_init(void)
{
ret_code_t err_code;
...
I am creating a system (nRF52 SDK11.0.0 s132) that will get a data ready interrupt on a GPIO (configured via GPIOTE with a handler) from a sensor every 4ms. The sensor has...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
