Hello,
we are testing software with the nRF54L15 DK with the 3.0.2 SDK and toolchain.
When creating a board configuration we use:
nrf54l15dk/nrf54l15/cpuapp
optimize...
Hello, I have an nrf52840 which is acting as a central. I have a peripheral device which I can connect to, and the service that is discovered has the following table:
ATT...
Hi, We are trying to get our nRF54L15 running, but are running into clock issues. The hardware is configured without an external 32kHz crystal, so we want to rely on the NRF54...
Hello!
I'm taking some performance metrics for encrypting data on my nRF52840 device and I was wondering if you might be able to help me. The goal is to see how long and...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
Gentlemen,
I apologize if this is not the correct place to post this question.
I have a potential project to start a BLE project but their requirement would be start...
I'm developing a new board with nRF8001, after reset i correctly get the DeviceStartedEvent 0x03 0x081 0x02 0x00, after that i go into setup mode sending the configuration...
Hi,
I am using nRF5_SDK_11.0.0_89a8197 at center to debug ble_app_uart_c project.
The center can connect the device well at the beginning. But if I power on and power off...
according to the introduction of mesh framework( value storage part), it says all mesh data is saved in a structure. My understanding is : Handle means a trickle instance...
How to configure S130 Softdevice as Completely Central(S120) i.e with Out Switching its mode to peripheral to operate like a central.
Is there any API or Example to do...
For example, if the first page is erased then it will set this page as swap page and continue looping without increasing the 'page' variable.
This means that the last...
Hi,
I have flashed boot loader to 0x7A000 (Size 24kb) and Softdevice to NRF52 DK ,then flashed application using nRF connect .
Am also able to update application after adding...
Hi,
I need PWM on 2 pins, with a varying duty cycle, and read some posts in this forum on the subject.
I am still using SDK7.2.0, with SD7. Our product is stable, so I...
Hello, a few days ago I was having trouble with RF performance on a custom PCB using the NRF51822. I posted here to get feedback and figure out where the design went wrong...
sdk : v8.1.0
os : ios
tool : nrf tool uart
use the ble_app_uart, it worked normaly. and add duf fuction in the application by the notice
[http://developer.nordicsemi...
Dear all
I found that the frontline BPA sniffer can't catch the connection data between Android5.1 or ISO and BLE device. Does this normal? How can I use the sniffer to...
Hello, I have to implement infrared sending and receiving of a modulated signal in pre-existing code.
I have managed to implement infrared sending thanks to the ble_app_uart_IR...
Hi!
I have creat two timer with app_timer_init.
start the first timer trigger every 4 ms, every 125 times(approximately 0.5 sec) to start the second timer which trigger...
I am having issues using the correct definition for the clock config:
for
nrf_clock_lf_cfg_t clock_lf_cfg = NRF_CLOCK_LFCLKSRC; SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL...
Hi,
I have very trivial question. I open the template program which is attached in SDK 11.0. In application timers start function I wrote the following code. The result...
