Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
Hi to everyone,
I'm trying to use the CMD Mode of my Sniffer but I have different problems. First of all, when I switch to the CMD Mode the red LED didn't blink (it doesn...
`Hi Guys,
I have some sensor data of 20 bytes at each measurement at different period stored in EEPROM. Now i have to transmit all data over BLE continously.
example ...
I have a laser distance sensor module. I want to connect this module with my nRF52 DK(PCA10040). The module communicates over UART:
Supply (2.8V-3.2V VDC) connected...
I want to purchase a BLE development kit. My current preference is nRF51 because there are more nRF51422 BLE modules in the market.
www.nordicsemi.com/.../3rd-Party-Bluetooth...
hi,
I'm using ble central example using S130 softdevice . It works fine without editing anything. In my application, I dont want to put the nrf51822 to System On low power...
We are seeing random connections on our peripheral devices and we have tracked them to a Mac Pro. The computer has never been paired with any BLE devices so we have no idea...
hi
in this pic CODE_R1_BASE is 0x16000 and amount is 88kB
how its size in keil is 0x29000
if i calculate ram we have 8kB
8*1024 = 8192 that is in hex 0x2000 its...
How can I advertise a custom service and the Device Information Service?
I tried the following, but only my custom service is visible in the Nordic Master Control panel...
Hi there,
I'm issuing a STOPRX at a specific time but I'm noticing that more bytes are being put into the buffer from after the STOPRX was issued.
Is there a way to...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
Continuing with my attempts to get this to work on SES I'm not sure if I'm missing something simple or not.
So using the excellent RKNRFGO (which by the way is much quicker...
There is an error in the gcc makefile included with SDK 5.2.0 that prevents it from detecting when a header file has changed and automatically recompiling the C files that...
Hi all,
I've always been a CSR developer and recently been asked to develop on the Nordic chip. The example code makes sense to me and its not to different to the CSR code...
