Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
Hello,
I have a design where nrf51422 works as companion chip together with an other uC as main controller (STM32F4).
I need to reset the NRF from the main controller...
Hi,
For our new product we are using nRF52832 chip for BLE and NFC. We have a query regarding the NFC section which is listed below-
Please refer the recommended EMC filter...
I have captured the ble packet showing as the screenshot by using the ble sniffer(win7 ) and wireshark.
But I did not understand the meaning of delta time (such as end to...
Hello!
I would like to whitelist a peripheral when -60 dBm RSSI is achieved (this means that central will bond to peripheral by proximity) but later data exchange must...
Hi all, i have an application with a smart beacon kit; i won't resume the whole project because it's long and boring, i will just say that i have a service that every 100...
Hi,
I'm using the S110 v8.0 on a nrf51422 together with our own scheduler with a few lines left from SDK v8.1.
I'm sending out advertising containing some extra data and...
Dear
As far as I know, the nRF51822 has the Pin Crossbar feature that weu can chose and connect
any GPIO pins as second UART.
I need to talk to two UART peripherals...
Hello Everyone,
I have created an schematic for m custom prototype using NRF51BLE with Sigfox Radio chip whenever i press the button on the NRF51i has to send message to...
Hello,
is there a trick, how the Radio peripherals device address match feature could be used to implement those advertising filter policies that filters based on the PDU...
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development...
I have been using this mode to init the app_uart_fifo code on SDK8 for a while now and when moving over to the SDK11 code I was in the app_uart_fifo.c code and it's radically...
