When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi..
i am using softdevice 132 and android MCP.
i want to create .zip file for application, but it shows error like below..
C:\Program Files (x86)\Nordic Semiconductor...
Hi all,
I am facing a weird issue trying to achieve DFU over the air with the dual-blank DFU.
I had integrated DFU with my application(Background story here .) The application...
Hi
I have problem enabling gzll on my nRF51. Error diagnoses shows NRF_GZLL_ERROR_CODE_INTERNAL_ASSERT_OCCURRED (#15), every time I try to call nrf_gzll_enable();
Here is...
I've looked at the reference manual and the several forum questions asking the same question and do not understand the answers as they all seem to point to the same docs/original...
HI All,
We are using NRF52, S132 Softdevice , SDK 11.0.0.
In SPI DMA transfer, when we try to increase size of the m_tx_data greater than 254 bytes, it failed. It is working...
HI All,
I did all the things as in this post
devzone.nordicsemi.com/.../
But Whitelist is not working for me. My requirement is this, I need to add the first connected...
Hi everyone,
I must to program my device from nRFgo Studio (rel. 1.21). So I do this procedure:
I program the Softdevice (in my application S110 rel. 7.0.0);
I program...
I am using nrf51822 and I am trying to reduce the transmit range to 30 cm or less.Is it possible to achieve this. The reason I am doing this is that I will be working with...
Hi,
I want to use both SPI master & slave altogether, but when I include nrf_drv_spis.h upon compilation the following error occurs :
C:\Keil_v5\ARM\PACK\NordicSemiconductor...
I am trying to find out the lowest range of nrf51822 but so far I coulden't find anything. Most of the time people are trying to increase the range.Thanks.
Hi Guys.
I have compiled and programmed ble_app_uart program in to a nrf51DK (pca10028-nrf51488).
I downloaded and installed nRF UART V2.0 to android 5.1.1 .But while scanning...
Hi,all.i use pwm with sdk8.1 sample (SDK8.1\example\peripheral\pwm),my question is how to stop pwm and set the pin to low level? is my code correct?
my pwm init code:
...
I've a board with the nRF51 inside and a LIS3DH as accelerometer.
I already reflashed and I want to read the accelerometer values from the LIS3DH but I don't know where...
