Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hello,
I want to use packet length extension with the PCA10040 and SDK v12.
The peer will be the nRF51 dongle (PCA10031).
I believe that the nRF51 dongle doesn't currently...
I am still noticing a higher than expected power draw on my nRF52 and I want to make sure I have adopted best practice in turning things off/optimising things before entering...
Hi,
I am using a 128KB-rom 16KB-ram nrf51822 and trying to run blinky from SDK 11 with softdevice.
If I load nrf51 S130 1.0.0 softdevice, and use the following in my...
As of SDKV12, because of the removal of pstorage, I upgraded my app to use fstorage.
If you look at the SDKV12 doc at this link, you will notice that it is quite lacking...
Hi,
I am trying to write some data into the flash of the nRF52832 SoC, but can only write around 5 kb of data. After that I will get an error of number 7, which should...
I'm using SDK v11, nRF51
I started developing with S130, v2.0.1
The device is peripheral only, so I decided to switch to S110 v8.0.0, since I need the memory.
I made...
I don't have a particular issue right now, just a concern that I have because my device needs to be bulletproof when it comes to reset behavior.
When sd_mbr_command(SD_MBR_COMMAND_INIT_SD...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
Hello,
I'm developing nRF52 with Keil5.14.
Before I used nRF52_SDK_0.9.2 and it worked fine.(With NordicSemiconductor.nRF_DeviceFamilyPack.8.0.3.pack)
I upgrade the...
Hi all
According to the following post, the RAMONB register doesn't exist since the nRF51822 has only 2 RAM blocks: devzone.nordicsemi.com/.../
But the current version...
Hi, i use the SDK11 and i will send and receive beacon and be able to launch a BLE DFU.
I am able to make a software in wich i can receive and send BEACON but in...
I'm trying to upload via DFU from one nRF51822 to another nRF51822 via DFU
The receiving side is not a problem as there there are loads of examples.
But I can't find...
