Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
If I want to set transmit power to -4dB, these are the settings:
command=LE_TRANSMITTER_TEST (this wouldn't be used anyway)
freq=0x3C (meaning: -4dB)
length=2 (meaning...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
Are there plans to release the files for download instead of online-only access through the Infocenter? It was always so nice to have them on-hand to grep in the previous...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
Hi,
I'm facing a little problem with custom service characteristic. I've set char settings as follows
attr_char_value.init_len = sizeof(uint8_t);
attr_char_value.init_offs...
Although this is easily fixable, Nordic engineers should be made aware that they made a minor change in SDKV12 that breaks makefiles on the Mac.
In /components/toolchain...
Hi,
I have downloaded the latest SDK12 for nRF52.
And i tried out the new "BLE Secure DFU Bootloader" example.
But i found that doing the BLE DFU with nrfutil on...
Hi,
I have nrf52 DK and sdk11.
I want to implement the time using internal RTC , the clock should run if the power is off ,i'm implementing in central code ,it has to...
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I...
Hello. I have the need to get a device's unique address that remains stable across device firmware upgrades, etc.
Before SDKV12 I've been using sd_ble_gap_address_get(...
Hi
I want to know how to use ppi to wake up CPU from IDLE mode.
I've tried to use timer timeout event for triggering Port Event and wake up CPU, but can't assign NRF_GPIOTE...
