Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
main.c
I am new to nordic devices and currently working on MPR121 touch sensor via I2C on nRF52 device. Using an existing example "twi_master_using_app_twi" as a base,...
Hi
I want to start a new app with the nrf52 to port our app running on the nrf51.
I took as a starting point ble_app_template_s132_pca10040, renamed it, and changed...
Hi!
I get the RAM adjustment warnings when running my nRF52 system:
RAM START ADDR 0x20004000 should be adjusted to 0x20001FE8
RAM SIZE should be adjusted to 0xE018
...
In my application I send a characteristic notification from inside a timer callback function. This causes a restart of my application if I am connected to the board. But my...
It has developed a eddystone-url in nrf52 device based on the current nrf5-sdk-for-eddystone project.
But I would like to know the Nordic's policy about this.
In other...
Hello Everyone,
I wrote the simple software for long push 3 sec and long long push for 5 sec and it is working fine as expected but can anyone suggest me how to create...
Hi there.
I'd like to start measuring the current consumed by a custom board with an nRF51822 on it in various states using a scope. I've read the DK user guide advice...
Hi,
We've developed a prototype for a client and just received the nRF51 chips for production. Problem is that the chips that just arrived is an older revision than the...
Hello, I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated Continuous...
Hi all,
I'm having a tight deadline upcoming and have run into an anoying problem.
I'm using this NRF51 breakout board: ohtcom.com/.../nrf51-m0-module
I ordered a...
HI I am trying to make 5 characteristics on Nordic and my program does not compile for NRF51822 QF AA or AB. but compiles fine for QF AC. what could be the matter. I get an...
Hi,
At command, I'm sampling ADC for a short period of time. What I noticed is that the current consumption of the chip goes up 2mA, even after the sampling is stopped...
Hi,
What is the actual difference in hardware between the two chips? I know they support different soft devices but is there any actual difference in the hardware? Or is...
Does having monitor mode debugging or using RTT print statements increase the quiescent current of the nRF52 even when the debugger isn't connected? I am using S132 SoftDevice...
